All Posts

Why window and door testing starts with the assembly, not the brochure

22 Oct 2026

A brochure shows what a product is meant to do. Testing shows what the complete assembly actually does. A window or door can look finished and still have unanswered performance questions, and those questions are far cheaper to answer in a laboratory than on a project.

Most customers arrive with the same four questions: What do I need to test? How many tests are required? What standard applies? What happens if the product fails? Whether you are a manufacturer trying to avoid a failed test or a project team who needs evidence for sign-off, the answers start in the same place. Decide what performance needs to be demonstrated, and what the results will be used for.

1. Define the requirement before the sample

Start with four things:

  • Product type

  • End-use environment

  • Design or installation configuration

  • The applicable standard or nominated project criteria

Drawings, schedules and details of the assembly help the laboratory settle on a workable scope. The aim is to answer the right question, not just to run the most familiar test.

2. Match the test method to the complete system

For windows and doors, Azuma’s NATA-accredited testing covers AS 2047, AS 4420, NZS 4211 and AGWA ICP 002. Azuma has tested to AS 2047 and the AS 4420.1 to 4420.6 series since gaining NATA accreditation in 2005.

These are useful starting references, but a standards listing doesn’t cover every configuration. A single test report may not cover every product size, configuration or use case, and passing one test does not automatically establish compliance across a full product range. Confirm applicability for your exact product and check the current NATA scope.

A note on naming: AS/NZS 4420.1 is the test method called up by AS 2047, so you may see both in the same report.

Blog Breaker

3. Use the findings to make a better decision

A customer submitted a sliding door for testing to AS/NZS 4420.1 to meet AS 2047. The sample was tested for structural deflection, operating force, air infiltration, water penetration and ultimate strength. It struggled to meet the water penetration requirements.

Observing the sample during water penetration testing, Azuma identified three areas for improvement: the sealing of the sample, the fixed sashes and the position of the drainholes. Azuma advised on the design, and R&D exercises isolated and modified each issue. Once the sample reached an acceptable water penetration result, the customer returned with a fresh sample carrying every modification. It met the requirements.

The first result is not the end of the story. Understanding how the assembly responded is what makes the next change worth making.

The customer also took the lessons into how they design new windows and doors. The point is not that every product can be made compliant with one tweak. It is that evidence tells you where to look next.

4. Plan for the report and its reader

Before testing, agree who will rely on the report: your design team, a customer, an engineer, a certifier or a project reviewer. Azuma outlines sample preparation, fixtures, sequence, timing and reporting upfront, and the report should confirm:

  • Specimen identification

  • Relevant dimensions and variants

  • Test conditions

  • Acceptance criteria, where applicable

  • Any limitations

A clear evidence trail makes every later conversation about the product easier.

5. Your pre-test checklist

  • Drawings and details: material and configuration information for the assembly

  • Application: where the product will be used and the project requirements it must meet

  • Standards: the relevant standard, or a request for help identifying the right method

  • Sample logistics: sample quantity, installation arrangements and fixtures

  • Reporting: what the report must contain, plus a plan for investigation or retesting if needed

How Azuma can help

Azuma delivers around 500 reportable tests a year, backed by engineering support, standards guidance, in-house fabrication and R&D. It is part of the Alchin Long Group, with NATA accreditation (No. 15147), ISO 9001 and ISO/IEC 17025 alignment.

To help us prepare a quote, send your product details, drawings or specifications, and the required standard if you know it. Not sure which standard applies? Tell us what you want to assess and we’ll help clarify the testing approach.

📧 contact@azumadesign.com.au
📞 (02) 9604 0255
📍 38 Redfern Street, Wetherill Park NSW 2164